|
HD-SDI, HD-HDMI(DVI) Interface Boards for FCB-H11
and FCB-EH4300 Sony Block Cameras
The EH43 Series is a family of small form factor modules for formatting and converting generic digital video streams to standard compliant formats. Different interface standards are supported from the transmitter side including DVI/HDMI, VGA, HD-SDI, SDI and USB. The modules connect to the digital video interface of Sony’s FCB-H, FCB-EH and FCB-EX block cameras and support several progressive and interlace HDTV or SDTV formats. As no analog to digital conversion is done on these modules, best output image quality is guaranteed.
|
EH43 - Features |
+ Connects to Sony FCB-EH4300 and FCB-H11/H10 HDTV camera blocks + Digital LVDS video input from camera + 1080i, 1080p and 720p output standard support + 25Hz, 29.97Hz, 30Hz, 50Hz, 59.94Hz and 60Hz frame rates + Automatic input standard detection + Dual HD-SDI outputs to drive two cables simultaneously + HD-SDI outputs compliant to SMPTE292M / SMPTE274M / SMPTE296M + HDMI video output + Integrated deinterlacer1 for 1080p 50/59.94/60Hz output via HDMI port + Native digital signal processing chain for best image quality (no scaling) + Breakout of camera analog HDTV YPbPr and CVBS video + Selectable serial control interface (RS232 or 3.3V TTL) + Supply voltage: 7V to 12V DC regulated + Tiny module size 46mm x 42mm + Triple output version EH43-SH and HDMI only version EH43-H |
Block Diagram for EH43 |
|
|
Order Codes:
|
Specification Camera Interface |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
INPUTS: |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
DATA |
LVDS digital video (from camera) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
CLOCK | LVDS (from camera) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
CONTROL Rx |
3.3V TTL serial control interface | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ANALOG |
YPbPr and CVBS video 1Vpp into 75 ohms | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
OUTPUTS: |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
CONTROL Tx |
3.3V TTL serial control interface | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
RESET |
3.3V TTL, active low, for FCB-H11 only | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The camera type is selected by onboard jumper setting. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Power and Environment | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
POWER INPUT: OPERATING CONDITIONS: STORAGE CONDITIONS:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Board Mechanical | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Connection Example | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Image shows EH43 connected to FCB-H11(left) and FCB-EH4300.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Video Standard Selection Tables for FCB-EH4300 Solutions | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The video standard provided by the camera is automatically detected by the EH43-SH/EH43-H module. EH43-SH/H JP1 Jumper Pins 3-4 OPEN. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Table 1 Video output matrix for EH43-SH with FCB-EH4300 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Table 2 Video output matrix for EH43-H with FCB-EH4300, HDMI output only Note: Refer to Sony FCB-EH4300 manual on camera operation and setting adjustments
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Video Standard Selection Tables for FCB-H11 Solutions | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The video standard provided by the
camera is automatically detected by the EH43-SH/H JP1 Jumper Pins 3-4 OPEN. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Table 4 Video output matrix for EH43-H with FCB-H11, HDMI output only Note: Refer to Sony FCB-H11 manual on camera operation and setting adjustments |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Analog Video Output | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
EH43-SH and EH43-H provide analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. The signal availability in different modes depends on the capabilities of the camera model used. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Reset Operation | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
When applying power to EH43-SH and EH43-H, the camera is also automatically powered. During power up all functions on EH43-SH/H are reset. During operation a manual reset can be applied by pulling pin no. 7 of connector J7 to 0V (GND). This resets also the camera. Note: Actual FCB-EH4300 camera does not support manual reset operations (March 2011).
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Camera Control | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Camera control can be done by connecting a PC or CCU via RS232 or serial 3.3V TTL interface to
EH43-SH/H. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of jumper JP1, pins 1-2.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Cable Kit Contents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
EH43CK-H11, Cable kit for FCB-H11 solutions: External connecting cables: 1 pcs. - 10pin flying leads cable for power and control, lead length = 10cm / 3.94inch 1 pcs. - 8pin flying leads cable for analog video, lead length = 10cm / 3.94inch 1 pcs. - 8pin flying leads cable for manual reset and mode_1080 select, 3 leads, lead length = 10cm / 3.94inch Camera connecting cables: 1 pcs. - 10pin KEL SSL type micro coaxial cable, connector on both sides, length = 12cm / 4.72inch 1 pcs. - 24pin FFC cable for manual reset and mode_1080 select, 3 leads, lead length = 10cm / 3.94inch
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Total Turnkey Solutions. All rights reserved. Specifications subject to change without notice.